New South Wales - NSW Sydney-Nowra Route (Main Illawarra v3)
Route design by Brian Bere-Streeter

Overview

This route is based on the Main Illawarra railway lines running down the coastal strip of the Illawarra region of New South Wales, Australia, around the 1950 to 1965 period, from the Steam Platforms at Sydney Terminal to the final terminus at Bomaderry (Nowra).

Main Illawarra railway lines running down the coastal strip of the Illawarra region of New South Wales from the Steam Platforms at Sydney Terminal to the final terminus at Bomaderry (Nowra).

The route comprises the following lines:

  • Sydney (steam terminal) - Bomaderry (Nowra);
  • Unanderra - Moss Vale (first 10km/7 mi only);
  • Private lines of AIS Steelworks, Port Kembla, providing most of the steelworks traffic, including coal traffic, coke traffic, hot metal traffic, slag traffic, hot ingot traffic, and steel slabs and shapes traffic.

Mainline route length: 153km (95 miles).

Total track laid: 711 km (442 miles).
Track Pieces: 10,394 used

Copyright: any and all issues have been resolved.

Total mainline trackage: ~330km.
Stations and sidings: 32.

Prototype Operator: New South Wales Government Railways (mainline), AIS (Port Kembla steelworks)

 

File download names and links

Complete Install of v3.0: (single large data file version) best suited to users on broadband internet (data file is 175 MB).
Note there are two files:

AU_NSW_Mi3_Full_MSTS1_Setup.exe
AU_NSW_Mi3_Full_MSTS1_Setup.D01
OR

Complete Install of v3.0: multi-part version suitable for users on dial-up internet acess (each part is ~47 MB).
Note there are four files:

AU_NSW_Mi3_Full_in_parts_MSTS1_Setup.exe
AU_NSW_Mi3_Full_in_parts_MSTS1_Setup.D01
AU_NSW_Mi3_Full_in_parts_MSTS1_Setup.D02
AU_NSW_Mi3_Full_in_parts_MSTS1_Setup.D03

Important Notes:

  1. The two versions ARE identical - only the method and size of file preparation varies.
     
  2. This method of installer preparation reduces the time Vista and some anti-virus programs may take to scan the EXE file.
     
  3. You may need to right-click and "Save Link/Target As" on the .D0x files to save them to your hard disk instead of having them open in your browser.
     
  4. Read "Additional Files Required" further down this page: you will require more files.

 

File Sizes

Single large data-file version:

.EXE file:    1.21 MB (1,272,620 bytes)
.D01 file:    175 MB (183,991,862 bytes)

Multi-part version:

Suited for users on dial-up internet access, the installer is divided into four sections (all less than 50MB, the general dial-up time/bandwidth limit):
EXE, .D01, .D02:   47.0 MB (49,356,800 bytes)
DO3:                    46.8 MB (49,129,475 bytes)

 

Additional Files Required

  1. Xtracks 3.20 or higher
  2. Newroads 4.0 or higher

 

Tasks Required

  1. Download the two (or four for multi-part) files linked above; ensure both (or all four for multi-part) files are in the same folder in your PC.
     
  2. You must have all six default routes installed BEFORE running this installer. The routes just need to be present: they DO NOT need to be unstored if you use Trainstore, nor do you need to activate them if you use Route Riter's ON/OFF utility.
     
  3. You must have Xtracks 3.20 or higher installed.
     
  4. You must have Newroads 4.0 or higher installed.
     
  5. Run the installer by double-clicking on the EXE file (do not touch the data file - .D0n - the installer EXE will load the data pack itself). In the case of the multi-part installer, double-click on the EXE file to commence installation (do not touch the data files - .D01, .D02, .D03 - the installer EXE will load the data packs itself).

    The route will occupy about 560 MB of hard disk space. The installer is automatically set to "Run As Administrator" for Vista and Windows 7 users.
     
  6. Allow the batch file to run to completion. If you do not see this batch file run in a DOS box, you most likely are a Vista or Windows 7 user. TURN OFF "User Account Control" (Start | Control Panel | User Accounts | Turn User Account Control On or Off); then right-click on the installme.bat file in the Route folder and set "Run As Administrator". The batch file should now run correctly.
     
  7. The first time you run this route, there will be a short delay as MSTS "generates terrain buffers" - this is a one-off and subsequent use of this route will load normally.
     

 

Screenshots

137 Fast Passenger gets away from Albion Park as two student pilots practise their flying.
137 Fast Passenger gets away from Albion Park as two student pilots practise their flying

AIS DE5 about to dump a load of Slag from Blast Furnace No3.
AIS DE5 about to dump a load of Slag from Blast Furnace No3